- Home
- Products
- Oscilloscopes
- Analog Oscilloscopes
- TOS-2100C
Analog Oscilloscope 100MHz
★ Dual channel 100MHz
★ Time base auto-range
★ Cursor readout with 7 measurements
★ Panel lock function
★ Buzzer alarm
★ LED indicators
★ TV synchronization; X-Y mode
★ Z-axis modulation input; Trigger signal output
★ Signal delay function, monitoring the leading edge
★ Continuously adjustable screen illumination
★ Delayed sweep
★ 10 sets memory for panel settings save & recall
Vertical system |
||||||
Sensitivity |
2mV~5V/DIV, 11 steps in 1-2-5 sequence |
|||||
Sensitivity accuracy |
≤3% (5DIV at the screen center) |
|||||
Vernier sensitivity |
Continuously variable to 1/2.5 or less of the panel-indicated value |
|||||
Bandwidth (-3dB) |
DC (AC 10Hz)~100MHz (2mV/DIV: DC~20MHz) |
|||||
AC coupling |
||||||
Rise time |
Approx. 3.5ns (2mV/DIV: Approx. 17.5ns) |
|||||
Input impedance |
Approx. 1MΩ±2%//Approx. 25pF |
|||||
DC balance shift |
5mV~5V/DIV: ±0.5DIV |
|||||
Vertical mode |
CH1, CH2, DUAL (ALT/CHOP), ADD, CH2 INV |
|||||
Chopping repetition frequency |
Approx. 250kHz |
|||||
Bandwidth limit |
20MHz |
|||||
Input coupling |
AC, GND, DC |
|||||
Max. Input voltage |
400V (DC+AC peak), AC frequency≤1kHz |
|||||
Common mode rejection ratio |
50:1 or better at 50kHz |
|||||
Dynamic range |
5DIV at 100MHz |
|||||
Polarity (INV) |
CH2 |
|||||
CH2 INV BAL |
Balanced point variation≤1DIV (referred to graticule center) |
|||||
Signal delay |
Leading edge can be monitored |
|||||
Horizontal system |
||||||
Horizontal mode |
MAIN (A), ALT, DELAY (B) |
|||||
A (main) sweep time base |
50ns~0.5s/DIV, continuously variable (UNCAL) |
|||||
B (delay) sweep time base |
50ns~50ms/DIV |
|||||
Sweep time base accuracy |
±3%, X10 MAG: ±5% |
|||||
Sweep magnification |
X10 (Max. sweep time base: 5ns/DIV) |
|||||
Hold off time |
Variable |
|||||
Delay time |
1us~5s |
|||||
Delay jitter |
Better than 1:20000 |
|||||
Alternate separation |
Variable |
|||||
Triggersystem |
||||||
Trigger mode |
AUTO, NORM, TV-V, TV-H |
|||||
Trigger level lock |
Not provided |
|||||
Trigger source |
CH1, CH2, LINE, EXT |
|||||
Triggersystem |
||||||
Trigger coupling |
AC, DC, HFR, LFR |
|||||
Polarity |
“+” or “-” polarity |
|||||
Sensitivity |
Mode |
Auto |
Norm |
TV |
||
Frequency |
10Hz~20MHz |
20MHz~100MHz |
DC~20MHz |
20MHz~100MHz |
Sync signal |
|
INT |
0.35DIV |
1.5DIV |
0.35DIV |
1.5DIV |
1DIV |
|
EXT |
50mVpp |
150mVpp |
50mVpp |
150mVpp |
200mVpp |
|
TV sync |
TV-V, TV-H |
|||||
Trigger level range |
INT: 4DIV or more, EXT: ±0.4V or more |
|||||
External trigger input |
Input impedance: Approx. 1MΩ±5%//Approx. 25pF Max.input voltage: 400V (DC+AC peak), AC frequency≤1kHz |
|||||
X-Y mode |
||||||
Sensitivity |
X-axis, Y-axis selectable X-axis: CH1, CH2, 2mV~5V/DIV, ±3% Y-axis: CH1, CH2, 2mV~5V/DIV, ±3% EXT: 0.1V/DIV, ±5% |
|||||
X-axis bandwidth |
DC~500kHz (-3dB) |
|||||
Phase error |
≤3° at DC~50kHz |
|||||
Output signal |
||||||
Trigger signal |
Voltage: Approx. 25mV/DIV into 50Ω termination Frequency response: DC~10MHz; Output impedance: approx.50Ω |
|||||
Calibration signal |
Waveform |
Positive-going square wave |
||||
Frequency |
1kHz±5% |
|||||
Duty ratio |
<48:52 |
|||||
Output voltage |
2Vpp±2% |
|||||
Output impedance |
Approx. 2kΩ |
|||||
Z-axis input |
||||||
Coupling |
DC |
|||||
Bandwidth |
DC~5MHz |
|||||
Voltage |
5V or more |
|||||
Max. input voltage |
30V (DC+AC peak), AC frequency≤1kHz |
|||||
Cursor readout |
||||||
Cursor measurement |
ΔV, ΔV%, ΔVdB, ΔT, 1/ΔT, ΔT%, Δθ |
|||||
Cursor resolution |
1/25DIV |
|||||
Effective cursor range |
vertical: ±3DIV; Horizontal: ±4DIV |
|||||
Panel setting |
Vertical: V/DIV (CH1, CH2), UNCAL, ALT/CHOP/ADD, INV, Probe factor, AC/DC/GND Horizontal: S/DIV (MTB, DTB), UNCAL, X10 MAG, delay time, HO Trigger: source, coupling, slope, level, TV-V, TV-H Others: X-Y, LOCK, Save/recall memory 0-9 |
|||||
Special function |
||||||
TIME/DIV auto range |
Provided |
|||||
Panel lock |
Provided |
|||||
Panel settings save & recall |
10 sets memory |
|||||
CRT |
||||||
Display |
6" rectangle, internal graticule 0%, 10%, 90% and 100% markers, 8x10DIV (1DIV=1cm) |
|||||
Phosphor |
P31 |
|||||
Accelerating voltage |
Approx. 16kV |
|||||
CRT illumination |
Adjustable at front panel |
|||||
General |
||||||
Power source |
AC110V/220V±10% selectable, 50/60Hz, Max. 65VA |
|||||
Accessories |
Power cord x1, Operation manual x1, Probe x2 |
|||||
Dimension |
310x150x455mm |
|||||
Weight |
Approx. 8kg |
Analog Oscilloscope |
|||
Model |
Bandwidth |
Channel |
Special features |
TOS-2020CH |
20MHz |
2 |
|
TOS-2040CH |
40MHz |
2 |
|
TOS-2050CH |
50MHz |
2 |
|
TOS-2020CF |
20MHz |
2 |
With 6-digit frequency counter |
TOS-2040CF |
40MHz |
2 |
With 6-digit frequency counter |
TOS-2050CF |
50MHz |
2 |
With 6-digit frequency counter |
TOS-2020CT |
20MHz |
2 |
With component test function |
TOS-2040CT |
40MHz |
2 |
With component test function |
TOS-2050CT |
50MHz |
2 |
With component test function |
TOS-2100C |
100MHz |
2 |
With dual sweep & delayed sweep function With cursor readout function |